How to Make a Wooden Wine Glass Rack for Wall Mounting
A wooden wine glass rack is an excellent way to store and display your glassware while saving counter space. Whether you’re a woodworking enthusiast or a beginner, this step-by-step guide will help you build a beautiful and functional wall-mounted wine glass rack.
Materials and Tools Needed
Materials:
- ¾-inch plywood or solid wood (pine, oak, or walnut)
- 1×3 or 1×4 wooden boards (for rails)
- Wood screws (1 ¼-inch or 1 ½-inch)
- Wood glue
- Sandpaper (120-220 grit)
- Wood stain or paint
- Clear polyurethane (optional)
- Wall anchors and screws (if mounting on drywall)
Tools:
- Measuring tape
- Saw (circular saw or table saw)
- Jigsaw (for slot cuts)
- Drill and drill bits
- Clamps
- Sander or sanding block
- Level
- Stud finder
- Paintbrush or rags (for staining or finishing)
Step-by-Step Instructions
Step 1: Plan and Measure the Rack
Decide on the size of your wine glass rack based on the number of glasses you want to store. A typical wine glass rack slot width ranges from 3 ½ to 4 inches, depending on the base diameter of your glasses.
Basic Rack Dimensions:
- Width: 16-24 inches (depending on available space)
- Depth: 8-12 inches (enough for stemmed glasses)
- Height: 8-12 inches (customizable)
Step 2: Cut the Wood Pieces
Cut the main back panel, rails, and support brackets according to your desired dimensions.
Basic Parts:
- Back Panel – A rectangular board that serves as the base for mounting the rack on the wall.
- Glass Rails – These hold the wine glasses by their base and allow the stems to slide in.
- Side Supports – Vertical pieces that hold the rails in place.
Use a table saw or circular saw for straight cuts and a jigsaw to cut slots for the glass stems.
Step 3: Create Slots for Wine Glass Stems
To hold the glasses securely, create evenly spaced slots in the rails.
Slot Measurements:
- Each slot should be 1 ¼ to 1 ½ inches wide to accommodate most glass stems.
- Leave about 3 ½ inches between slots for glasses to slide in without touching each other.
How to Cut Slots:
- Mark the slots on the rails.
- Drill a hole at the end of each slot (large enough for the jigsaw blade).
- Use a jigsaw to cut the slots along the markings.
- Smooth edges with sandpaper for a refined look.
Step 4: Assemble the Rack
- Attach the Rails: Use wood glue and screws to secure the rails to the side supports.
- Mount the Back Panel: Secure the assembled rack to the back panel using screws.
- Check the Alignment: Ensure that all slots are even and glasses slide in smoothly.
Use clamps to hold the pieces together while drilling to prevent movement.
Step 5: Sand and Finish
- Sand all surfaces with 120-220 grit sandpaper to smooth any rough edges.
- Apply stain or paint to match your decor.
- Seal with clear polyurethane for a protective finish (optional).
Allow the finish to dry completely before installation.
Step 6: Mount the Rack on the Wall
- Find the Studs: Use a stud finder to locate secure wall studs for mounting.
- Mark Mounting Holes: Mark and drill pilot holes on the back panel.
- Secure with Screws: Use 2 ½-inch wood screws to fasten the rack into studs or use heavy-duty wall anchors if mounting on drywall.
- Check for Leveling: Use a level to ensure the rack is straight.
Final Touches
- Test the rack by sliding in a few glasses.
- Adjust any loose parts if needed.
- Enjoy your new handcrafted wine glass rack!
This DIY wooden wine glass rack not only adds a stylish touch to your space but also keeps your glassware organized and easily accessible.
👉 For more amazing woodworking projects, check out Teds Woodworking Course here:
Click Here to Access